• <ins id="isgze"></ins>
  • <center id="isgze"><nav id="isgze"></nav></center>
  • <button id="isgze"></button>
  • 和人妻隔着帘子按摩中字
    简体中文 | English
    搜索:
    首页 关于我们 产品展示 新闻资讯 服务帮助 产品认证 案例展示 技术支持 联系我们
    当前位置 : 首页 > 技术支持 > Pipe Bender Operation >
    技术支持
    - Elbow Classification
    - Pipe Expander Maintenance
    - Pipe Bender Operation
    - Plate Rolling Machine Use and Maintenance
    产品分类
    弯头机
    弯管机
    扩管机
    三通机
    压力机
    坡口机
    模具
     
     
    Pipe Bender Operation
    How to Use IF Heating Pipe Bending Machine

    The IF heating pipe bending machine can be used to bend pipes made of alloy steel, carbon steel, and stainless steel. It is an important piece of equipment to provide bent pipes for construction projects in petrochemical, electric power, and other fields. The operation method of induction bending machine is detailed below.

    1. Install the steel pipe to be bent in place;
    2. Adjust the bending radius via the screw-nut transmission device on the rocker arm rotating device;
    3. Heat the steel pipe by the medium frequency induction heating coil to some temperature and start bending;
    4. The steel pipe is pushed ahead hydraulically and it is deformed at the heating part to bend;
    5. After the steel pipe deforms, spray water at it to cool it down. Thus, the required bent pipe is obtained.

    The steel pipe bent by our induction bending machine features no stress and small wall thickness difference. The bending radius is adjustable within the range of 0 to 180 degrees.

    Precautions
    1. Before operating the induction bending equipment, prepare the equipment according to the IF power supply and IF transformer manuals. Start the equipment cooling water pump.
    2. When the IF transformer is running, even with no load, it is strictly prohibited to stop the supply of cooling water. Waterway should be smooth to prevent water splashing on transformer.
    3. It is allowed to open the main motor to start bending only when the steel pipe is heated to the temperature sufficient for bending and the pipe inner wall temperature is above 910℃ but lower than the permissible maximum heating temperature. It is strictly prohibited to start the main motor if the required bending temperature is not reached or the pipe is not heated. When bending is over and heating is stopped but the chuck is not released, it is also banned to start the main motor for the returning of rocker arm.
    4. Before bending, the steel pipe should be carefully adjusted to make the chuck center consistent with the induction coil center. Also, the wheel used to support the pipe should be adjusted to a suitable height, so as to ensure that the pipe is fed smoothly and the bending part is in the same plane with the straight part.

     
    最新产品
    - 优良弯头机
    - 制造中频弯管机
    - 制造弯管机
    - 热推中频弯头机
    - 三通机工艺
    - 供应推制机
    - 新型中频弯头机
    热门产品
    - 315T四柱式压力机
    - 主 5000T四柱式压力机
    - 500T四柱式压力机
    - 扩管机
    - 1000T龙门式压力机
    - 1620mm 链条式弯管机
    - 820mm 液压中频弯管机
    推荐产品
    - 315T四柱式压力机
    - 主 5000T四柱式压力机
    - 500T四柱式压力机
    - 扩管机
    - 1000T龙门式压力机
    - 1620mm 链条式弯管机
    - 820mm 液压中频弯管机
    快速检索产品
    ?
    联系我们
    沧州奥广机械设备有限公司
    地址:河北省沧州市孟村回族自治县泊北工业区
    邮编 : 061000
    手机:15230713671
    传真: 0086-317-6218625
    邮箱:15230713671@163.com
    关于我们 |  产品中心 |  在线留言 |  联系我们 Copyright © 2015-2016 沧州奥广机械设备有限公司 版权所有 后台